Could a platinum member mock this up in the generator for me?

[Mazz]

Just a custom idea I'm thinking about when I get a job and start getting money XD

Construction Neck-Thru Guitar
Construction Options None
Body Description Soloist
Body Wood Alder
Top Wood Options Flame Maple 1/8" Thick Top
Body Binding (Front) White
Body Binding (Back) None Other Body Options None
Body Scalloping None

Neck Description Jackson Style
Headstock Regular
Neck Wood Quartersawn Maple
Neck Option Three Piece (No Scarf Joint)
Fingerboard Wood Ebony
Fingerboard Inlays (Mother of Pearl except where noted) Sharkfin - Regular
Fingerboard Inlay Options Use Abalone instead of Mother of Pearl
Nut Width Guitar: 1 11/16"
Butt Width Guitar: 2 1/4"
Scale Length Guitar: 25.5"
Number of Frets Guitar: 24
Fret Wire Jumbo
Fret Scallops None
Neck and Head Binding Neck and Headstock
Neck and Head Binding Color White
Neck and Head Binding Options None
Neck Back Shape Standard - like SL-1

Bridge Tune-a-matic
Bridge Recess (Floyd Rose bridges only) Standard Tremolo Recess
Nut Non-locking - Graphite
Jack Location Side of Body
Jack Type Oval Plate
Strap Buttons Standard Jackson 17mm
Tuners Standard (Jackson logo)
Hardware Color Chrome
Knobs Metal Dome
Pickguard and Control Mounting No PG - Rear-loaded Controls
Battery Cavity 9 Volt
Truss Rod Cover Engraved with initials (specify below)
Pickup Route 2 HUM
Pickup Bezels Chrome
Active Electronics None
Covered Pickup Yes
Pickup Options (specify precise model desired below) EMG (2H)
Volume Control Knobs Two
Tone Control Knobs None
Knob Options Metal Dome
Other Controls None
Pickup Selector 3-Way Blade
Other Switches None

Color / Finish Transparent Blue Finish Options (for solid-color Rhoads, Kelly, and King V only) None
Neck Finish Painted Neck
Pickup Finish None
Headstock Type Standard
Headstock Color Match Body Color
Headstock Options None
Logo Color Abalone

This is not final specs as I am keeping these in mind and making changes where necessary.

Also, do the CS do non-bevelled (?) soloists?

Thanks.

[Mazz]

Also I am aware I did not need to post the whole thing, I just couldn't be assed doing anything past copy & paste XD

[Newc]

So basically you want a mockup of a Soloist with a trans blue flametop, matching regular 6-inline head, abalone finlays on ebony board, white binding on head, neck, and front of body, 24 frets, stringthrough/TOM, 2 EMGs, chrome hardware, chrome rings, blade switch, 2 knobs, and abalone logo?

And yes, they can do a non-beveled Soloist.

[neilli]

Isn't that just a SL2T with EMGs? Don't they do those in trans blue?

[shreddermon]

Soloists don't have bevels. Beveled edges are on RRs, KVs, Warriors and Kellys.

[Nightbat]

Support the site, become a platinum member and you can mock up all you want

[zuppermuhle]

Something like this? I assume by "non bevel" you mean without cutout for the right arm because you also wanted binding.

[Mazz]

Something like this? I assume by "non bevel" you mean without cutout for the right arm because you also wanted binding.

Quite similar to that, it's the trans blue shown on Jacksons website image #6 to #8 on the SL1, atleast I think it's trans blue....
http://jacksonguitars.com/products/p...uct=2803070803

[Mazz]

Soloists don't have bevels. Beveled edges are on RRs, KVs, Warriors and Kellys.

That is why I put (?) next to non-bevelled.

[Mazz]

Support the site, become a platinum member and you can mock up all you want

Trust me, if I had the money I would.

[jackson1]

You can buy the generator for $17.

[MetalHeadMat]

I'm kind of surprised this thread isn't deleted. I dunno if it's against the rules or anything, just me thinking out loud.

I wont tell, and that soloist looks FIIIIIIIINE.

[Mazz]

You can buy the generator for $17.

I did post earlier in this thread that I don't have the money and before you go saying "Well if you don't have the money for the Generator you surely won't have enough for a CS" then just incase you didn't read my first post either "Just a custom idea I'm thinking about when I get a job and start getting money XD".

[jackson1]

I read your posts and simply wanted to inform you about the generator price in case you didn't know.

Now it strikes me as pretty amazing that you can't save up 17 bucks over maybe a few weeks/months by cutting down on <you name it> stuff. Having the generator on your pc, you could enjoy making mockups all day instead of relying on JCF'ers doing you a few.

[RacerX]

Mazz, I'll pay half of the $17 if you can scrape up the rest!