Announcement

Collapse
No announcement yet.

Help with TB12 Screamin Demon wiring!!

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Help with TB12 Screamin Demon wiring!!

    I have a dissasembled one. Coming off of the coils is has:

    Hex Poles: Black and a white wire

    Screw Poles: red/white (these were factory soldered together), white, black and green.

    If I recall... the white wires from coil 1 and 2 were soldered together
    The black wires from coils one and 2 were also soldered together.
    The green and the black from the slotted screw coil were soldered together.

    Anyway, I tried every configuration possible and I can only come up with 5.7K ohms which I am sure is only 1 of the coils.

    Can anybody help.

  • #2
    If your green and black are soldered together, that could be the problem. Black is the 'hot' lead to the volume pot. Green and bare go to ground:
    Hand-crafted electric guitar pickups, acoustic guitar pickups, bass pickups and pedals. Helping musicians find their signature sound since 1976.


    Black and white come from one coil set, green and red from the other:

    The white and red soldered togther 'connect' the two coils and give you the humbucker with the 10kohm reading that a Screamin Demon should have (bridge position).

    The fact you are getting half that measurement means you are correct in that you are only getting one coil, I think because your green and black are connected to each other.

    Comment


    • #3
      Green and black both are interchangeable as Ground or Hot Lead. You can swap them for various phasing issues with other pickups.
      I want to depart this world the same way I arrived; screaming and covered in someone else's blood

      The most human thing we can do is comfort the afflicted and afflict the comfortable.

      My Blog: http://newcenstein.com

      Comment


      • #4
        Just to be a little clearer.. I am talking about the wires coming directly off of the coils. This pickup is completely disassembled. I need to rewire it completely.

        Comment


        • #5
          This might help with the color vs. what is what

          Anderson, Bare Knuckle, Bartolini, Benedetto, Bill Lawrence, Caparison, Carvin, DiMarzio, Dunca Designed, EMG-HZ, Fender, Fralin, GFS, Gibson, Golden Age, Gotoh, Ibanez, Iron Gear, Joe Barden, Jackson, Kent Armstrong, Lace, Lollar, Lundgren, Nordstrand, Paul Reed Smith, Peavey, Railhammer, Rio Grande, Rockfield, Seymour Duncan, Shadow, Sheptone, Suhr, Swineshead, TDM, Tone Rider, TV-Jones WCR and more.
          Tone is like Art: Your opinion is valid. Listen, learn, have fun, draw your own conclusions.

          Comment


          • #6
            OK I think what you need is this:

            (If your pickup has the hex poles closest to the bridge then swap the wiring below)

            Screw Poles: (closest to bridge on a TB-6)
            Black from Pickup to Green 4 Conductor
            White from Pickup to Red 4 Conductor

            Hex Poles: (closest to the neck pickup on a TB-6)
            Black from Pickup to Black 4 Conductor
            White from Pickup to White 4 Conductor

            Then to wire, solder the Red and white together, shield and green to ground, and black is hot (or just look at a diagram above for your wiring needs to pots/switches)

            I don't think you should connect the white to white and black to black from the coils (as mentioned above).
            Last edited by z1n; 01-04-2007, 12:04 AM.

            Comment


            • #7
              Also you can just connect the whites from both the coils together (thats what you are doing when you wire the red to white) then run black from one pickup as your hot and ground the other black wire along with the shield. gl

              Comment


              • #8


                solder b & d together for series opperation.
                Last edited by Dreamland_Rebel; 01-04-2007, 10:07 AM.
                Widow - "We have songs"

                http://jameslugo.com/johnewooteniv.shtml

                http://ultimateguitarsound.com

                Comment


                • #9
                  Great freaking post shoulda asked here before "expirementing" lol man i need to sleep more often!
                  Haters gonna hate
                  Dilluting the brand one MUTT at a time.

                  Comment

                  Working...
                  X