Announcement

Collapse
No announcement yet.

DiMarzio FRED and PAF Joe?

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • #16
    Originally posted by straycat View Post
    I thought you would tell him that Axewielder.
    Hehe I'm a Tech Q&A Question Whore! Even when they are posted in the wrong forum!
    _________________________________________________
    "Artists should be free to spend their days mastering their craft so that working people can toil away in a more beautiful world."
    - Ken M

    Comment


    • #17
      Me too.
      Really? well screw Mark Twain.

      Comment


      • #18
        Fred...

        I have a FRED in my 85' les paul studio and the kept the original PAF in the neck. The tone was much more detailed and worked very well with my mesa dual rec setup..metal, funk, blues...it does it all very well. Now the LP is mahogany, its a black studio that had chrome hardware, the hardware was all replaced with gold hardware, very shiny and plays like GOD. I love the FRED, never looked back.

        I can nail most harmonics easily, zakk squeals, van halen harmonics etc..

        Comment


        • #19
          Originally posted by straycat View Post
          Getting too close to the strings will hurt the sustain/harmonics of the pickup keep that in mind.
          from the Dimarzio website faq section.

          "How high should I adjust my pickups for the best sound?

          There is no specific distance that works best for everyone. We measure string height from the top of the polepiece to the bottom of the string when the string (usually the high or low E) is held down at the highest fret. For standard, full-size humbuckers, a reasonable starting point for the bridge pickup is at least 1/16" (1.5mm) from the high E and 5/64" (2 mm) from the low E. There are no recommended distances for the other 4 strings. Their polepieces should be adjusted (if necessary) by ear in relation to the volume established for the first and sixth strings. Once the bridge pickup is adjusted to a useful distance, the neck pickup can be adjusted by ear for a good balance.

          For single-coil pickups and all hum canceling single-coil replacements with Alnico 5 rod magnets, we've found the following formula works very well: at the highest fret (usually the 21st or 22nd), the closest recommended distances from the top of the magnet to the bottom of the string are:

          Neck and middle pickups

          low E 1/8 (3.2mm)
          high E 3/32 (2.4mm)


          Bridge pickup

          low E 3/32 (2.4mm)
          high E 1/16 (1.6mm)

          The Virtual Vintage® 2.1, 2.2 and VirtuAL 2® models have low magnet pull, and so do the Virtual T™ and all of the Fast Track™ models, including the Chopper™, Cruiser® and Pro Track™. They can all be adjusted relatively close to the strings. At the highest fret the closest recommended distances from the top of the magnet to the bottom of the string are:

          Neck and middle pickups

          low E 3/32 (2.4mm)
          high E 1/16 (1.6mm)


          Bridge pickup

          low E 1/16 (1.6mm)
          high E 3/64 (1.2mm)

          These settings will provide a lot of presence and attack. For a more open 1950s sound, try adjusting the pickups 1/32 (0.8mm) further from the strings.

          What happens if I adjust my pickup too close to the strings?

          The closer the pickup gets to the strings, the stronger the signal that's sent to the amp. However, getting a pickup close to the strings brings the magnetic field closer, too. If the magnetic field is strong enough, it alters string vibration enough to make the guitar sound out of tune, and it can also cause string buzz and reduce sustain."
          Widow - "We have songs"

          http://jameslugo.com/johnewooteniv.shtml

          http://ultimateguitarsound.com

          Comment


          • #20
            Thats what I said DR.In a condensed sort of way.
            Really? well screw Mark Twain.

            Comment


            • #21
              Weird - I have my neck pickup at like 1.5mm and my bridge at ~4mm

              Comment

              Working...
              X